1989 Marathon governor
I am a nubie to the forum and to cart rebuilds. When working on my governor on the transmission the shaft dropped down and i am not sure where it needs to be placed back in the proper location. I have...
View ArticleBelt slipping going uphill
Have a question that has probably come up before. I have a 1993 club car ds that I rebuilt myself. New piston, bored cylinder, and all the other goodies. I installed a Jakes 6" lift with tires and...
View ArticleClik here to view.
Cushman Hawk Project 898769E - 644100
I decided that I wanted to build my own golf cart, so I bought a Cushman Hawk I like how well it was built, not sure what year it is, got the parts Manual 700954, still looking for the operators manual...
View ArticleKindigit design Yamaha
Watching Dave design and build custom Yamaha on Velocity channel :thumbup:
View ArticleG1 lift kit help
Does anyone make a bolt on lift kit for the g1 ? I'm new to the Yamaha g1 stuff and seen a few that require cutting some stuff. I'm looking for the easiest way to do it. Thanx for any advice. Jeff
View ArticleExtendaframe plan " b "
I have an old dead Club Car laying around. It has the clutch on the opposite side so I am assuming my motor wont work unless tranny is in reverse to go forward? Maybe I should stop assuming and wait...
View ArticleTreatment of battery lugs when the plating is removed
I am making a new set of cables for my cart as a part of a major re-build. I am using #2 wire and I am wondering what is the best method to protect the lugs from corrosion. I have ground the edges of...
View ArticleYamaha gas g9
G9 not firing I got firer to the red and whit wider going to the coil but none coming out to plug
View ArticleCarryall Jackshaft help
So I decided on swap a 420cc clone into my carryall. I know I have to run a jack shaft but I have seen 3 different kinds. 1. Clutches on engine side, sprocket on drive side 2. Sprockets on engine side,...
View ArticleWisdom from Don Plowman - G29 kit - Oil - RPM
Learned a lot here about new-to-me 2014 G29 Drive and about Plowman's kits and customer service. Everything said here is true. Spoke to Don first to clarify a few things I read here and about what I...
View ArticlePics of ezgo txt with 12x7 wheels
I have a 2001 txt and am considering some storm trooper 12x7 wheels. Does anyone have any pics with some 12x7 wheels on their txt? Wanna see how far they stick out. Mine will not have a lift either....
View ArticleNeed help quick!
2009 ex go 36volt Alltrax 500 amp controller New battery wire all around Cart worked fine this morning. She has never liked the cold. She bucks and jumps until she hits a certain speed then she smooths...
View ArticleSolenoid Wiring... apparently mine is different?!?
I have a 2001 EZGo TXT. Just bought it and the previous owner appears to have hacked it up a little. When I bought it, he said the charger was bad. Apparently, he just didn't know that the charger...
View Article2005 TXT Batt Meter LEDs 'Bouncing'.
Recharged the batteries last night and, this morning, when I turned the switch on, the battery gauge reading continuously jumps between the bottom two segments. Have never seen this in ten years. My...
View ArticleBig mistake
I goofed. I have an 89 cc resistor and coils. I was rewiring to all cables to:cry: 4awg and snapped a terminal post in the vglide by over tightening. There's still enough post for the lug to stay on...
View ArticleClik here to view.
G9 starter generator not charging?
I'm in the final stages of doing a clone swap in my G9 and while doing my final run through of the electrical side I found my starter generator was possiblly not charging, it starts the engine just...
View ArticleDoes the rear end hold up?
Just curious with changing from standard 295CC to up to 24HP motor increase, Has anyone had any issues with the stock rear gearing holding up?
View Article2000 36v TXT Series- Speed and Torgue Upgrade
I have a 4 Seater 2000 36v TXT Series Golf Cart that I'd like to upgrade the speed on. Currently all stock... (motor, controller, etc.) I'm very close to ordering a motor online... (Model# MOT-B1) that...
View ArticleQuestion why should we keep all the micro switches in a gas club car?
With so many options why should we keep all the micro switches in a gas club car? 9 times out of 10 they are at the bottom of many of the issue we face..Any opinions on this?
View Articlezemco header
Took this header off 295 cc robin its like new no gaskets for it took it off because its louder than stock looking for $100 plus shipping I live in central Pa. 17745
View Article