Yamaha G14 Parts
I am putting a Vanguard in my G14. The cart was run out of oil so the rod, wrist pin and piston are gone. The cam, crank, engine cover, carburetor, etc are all good. The block is also fine, likely...
View Articleprecedent motor wires are different sizes?
2011 precedent "PH11" advance motor I have my precedent motors rebuilt locally here. Usually, he drops one off to me, and i give him my old motor, as a core exchange. Here is my question, I installed a...
View Article2006 48V Club Precedent install Madjax Convertor
My wife wanted her golf cart refurbished and radio installed in her golf cart for Christmas. I really didn't know what I was getting into so I could use some help. I've already repainted the entire...
View ArticleShow me your DS carts on low pro 14s
I can't decide if I want a lift or lowered. I found a lot of pictures of lifted DS. So I want see some on low pro 14s thanks guys.
View ArticleDouble a arm vs long travel
Bought a G2 a few weeks back with a 3" lift kit. I want to go to a 7" kit. I want to go LT but that is twice the coin. The cart will not be well secured for the usable season so I don't want to spend a...
View ArticleHD Rear Leaf Springs
So I put the rear seat on my cart right after Christmas. Today I ordered some heavy duty leaf springs. Just for the fun of it I went to Youtube to see if there were any videos replacing the springs. I...
View ArticleI blame everyone here
Yes, I blame everyone here for contributing to my new addiction/hobby with the golf cart i have acquired. I have asked many a dumb questions and have received lots of supporting help and answers for my...
View ArticleClik here to view.
operation workhorse repower
Hello all. I have a 98 ezgo 1200 workhorse. since I bought it a couple years back I have put a 6 inch lift, a hydraulic lift cylinder on the dump bed, recovered the seat and new 8 inch wheels on the...
View ArticleRunning hot issue again
I know this subject has been rode hard already but I can't find a definitive answer. My '04 gas DS was fine until one day it wouldn't start, no spark. Figured out it was the ignitor. Disconnected the...
View ArticleService Manual for Older EZGO Cart Needed
I'm posted for my father - he has an older model EZGO cart that we aren't sure what year it is. He thinks it is in the 70's range - but he can't find ANY serial numbers on it at all. It's a 36V, all...
View ArticleHD Four stroke swap?
Haven't posted for a while. I am wanting to do a four stroke swap for my '76 HD three wheel since I use it mostly for parades and it doesn't want to charge at the low speeds and leaves me with a dead...
View ArticleHow do I replace speed control 07 PDS
I have a 2007 PDS need to replace speed sensor. Does the motor have to be removed?
View ArticleBad boy Buggie troubles
Have 06 bad boy that I've worked on customer brought in the batteries were 8 years old so figured just needed batteries switched the batteries to new one only thing the cart will do is show the battery...
View ArticleWTB Charging port for for a CC DS 48v
Im looking for a good 48 v charging port for my 96 cc ds. Any help would be great and thanks.
View ArticleSurging and reduced speed
2001 Club Car series cart - AA0130 6" lift with 23" tires Brand new Trojan batteries My cart has started to have reduced speed and power and also occasionally surges during constant throttle. It seems...
View ArticleWTB 6" a-arm lift and wheels and tires for CC DS
Im looking for for any used 6" front a-arm lift kits and rims and tires or just rims or tires for my 1996 cc ds 48 volt. Thanks guys!!
View ArticleEZGO DCS reverse microswitch
I had posted a message sometime back about my cart not going into reverse. I have definitely determined it is the microswitch. Someone suggested just bending the little metal arm and that seemed to...
View ArticleClik here to view.
1st carryall build
This is my first CC, I had a 2 stroke EZGO and G2 Yamaha that I sold to finance this cart. It was purchased in Albany GA. from a CC dealer who told me it came from FLA and was used at a collage and I...
View ArticleKey Start / Shifting
I have been doing alot of reading on the forum and I am trying to get some clarity on how guys are using key start and having the ability to shift from F-N-R with the engine running? I see the CPP Big...
View ArticleClik here to view.
XCT 500PDS and solenoid max RPM
I have installed, but can't meet max RPM. Here's a shot of the data. Thanks for looking. Attached Images Screenshot (15).jpg (275.0 KB) Screenshot (14).jpg (277.8 KB)
View Article