Motor suggestions
Been going through troubleshooting on another thread and motor seemed to checkout okay regard continuity testing... However, if I wanted to replace the motor since I am working on the cart anyway......
View ArticleClear over truck bed coating?
Looking at painting the roof of my 2011 precedent and thinking of going the truck bed coating route (Duplicolor Truck Bed Coating). Scuff, degrease, adhesion promoter then spray can Truck bed coating...
View ArticleAnyone bought from WheelzLlc?
I purchased a dash kit from WheelzLlc on Sunday (March 27) and it has not shipped yet (Thursday night now). 3 Emails to them and 2 phone calls (voicemail) with no response. I did a quick search and...
View ArticleMaking a 4 wire Voltage Reducer "keyed"?
I purchased a Tecscan VOLTSeasy which converts 48V to 12V (15Amp). There are only 2 in and 2 out wires though (no switched yellow). Is there an "easy" way to wire it to my keyed switch on a 2011...
View Article88 club car to play with
I bought this cart for the frame and front suspension to build a 4x4 single seat buggie out of, but for now I am wanting to play around with it to see how much performance I can get out of it. I...
View ArticleElectric or mechanical problem?
I posted about my 2005 Precedent a friend has this problem and I told her I would ask. When driving her cart, same model, it just stops, then when it goes again it almost jumps. I don't know how else...
View ArticleG1 no reverse.
1982 G1. Cart has no reverse. Starter runs when key is in reverse position but does not create spark (im guessing) since forward is working fine. I did the cdi fix found on this site but the same thing...
View ArticleWorkhorse Starter Micro Switch Replaceplacement
I have a 97 Workhorse that I suspect has a bad micro switch because if I just feather the pedal the starter spins fine, depress it further starts fine. But if you just mash down the pedal or even put...
View Article2001 ezgo pds 36v 6in lift torque and tire clearance issues
Hi, I just purchased a 2001 ezgo 36 volt pds and installed a 6 in Jakes lift and 23 in tires. When I turn sharp or flex at all the front tires rub on the body. What can I do to fix this? HD shocks?...
View ArticleTwo Questions, Melex 112.
Question 1. I am rewiring a 112 and I dont see a fuse in the diagram. I am thinking about ordering a 60A bolt-on fuse. Is this what is normally used for this 57A motor system? Question 2. The wiring...
View ArticleBattery charging issue
Both of the golf carts at my office have been out of service for going on 2 years. I finally talked the boss into letting me rework them. Both carts are identical. EXGO TXT w/PDS, I believe. Both have...
View ArticleFE290 engine runs better with breather hose off.
Been trouble shooting an issue on my 2005 Carryall / FE290. Cranks right up and runs for a short time and seems to stall out, almost seems to flood out. Pulled clean the carb, same issue. Installed the...
View ArticleClik here to view.
Limp Mode has me Walking Home
Hello forum, Was wondering if I could get some help on a perpetual problem I have been having for a year now. I work on Volvo's so I know my way around a wrench and electrical things. IIRC the cart is...
View ArticleNeed a measurment...
Could I ask one of my Briggs (16 to 20hp) brothers to take a measurment for me? Need a measurment from the "outward" edge of the intake manifold to the fan shroud. This set up would have the carb...
View Article2012 TXT Wiring help
Hey all been looking trying to find wiring diagram, I have a 2012 TXT I am wanting to put a unique keyed switch on it. the switch I purchased is 3 pin and when I took the switch out of the dash was...
View ArticleClik here to view.
2002 EZ-Go Txt - Vanguard 16hp swap
To start this build I picked up a 16hp Briggs & Stratton V-Twin and a CPP subframe. I decided to keep the pedal start so I ordered a pulley and clutch (comet) from CPP too. Original Engine Pulley...
View Articleg16 will not start
Good evening. My g16's oil light came on a few weeks ago. I parked it and forgot about it. A couple days later I walked by and noticed the light was still on. The next day when I went to put oil in the...
View Article
