Ignitor, limiter, coil?
I have a 94 Club Car. After reading many threads about intermittent and/or no spark I have: replaced plug, replaced ignitor and tested limiter by removing ground. It seemed like I had made headway...
View ArticleHigh voltage reading
I've got a 48v RXV running 4 US 12v XC Batteries. I recently installed a digital meter and it reads 52.5v 12 hrs after charging. I tested the voltage with my hand held meter and i get the same reading....
View ArticleReverse Lights
Hello BGW, I just bought a rebuilt/refurbished 2000 lifted gas EZGO. I was thinking I wanted to add a reverse light. Can I tap into the reverse buzzer to power a light?
View ArticleDouble A-Arm lift squeaking
Hey guys, for all of you with a Double A-Arm lift, what do you do to keep them from squeaking? I use my cart to hunt off of, and have spraying all the bushings every weekend with CLP Break Free to make...
View ArticleEnclosures
Hi all, I am looking to purchase an enclosure for my 2007 St 480 workhorse. I have been looking on some websites and I have found there is are many different types, and as many different sellers. I...
View ArticleClik here to view.
How do I remove the driven clutch
There is no bolt on the end. Is there supposed to be and it's broken off? Or does the clutch somehow spin off? Hopefully somebody can help me cause I'm at a loss. Anybody know any tricks to this?
View ArticlePrecedent with 25" tires???
Have any of you guys had any experience putting 25" tires on an electric Precedent? I'm running 23" Raptor mud tires right now, and they're just to flat of a tread profile to get enough traction in the...
View ArticleWandering Steering on Marathon
Recently bought a '94 Marathon. Steering wandered a LOT. Replaced rack/rod end, got better but still wanders. Where is the most LIKELY area to look next? Wheel bearings? King pins? Tie rod ends? Would...
View ArticleCoil clearance from flywheel?
What gap do i set the coil at from the flywheel? Anybody have any recommendations?
View Article99 CC only goes 12mph
Hello, All I have a friend that bought a 99 club car that only goes 10 MPH then he put on bigger tires and now only goes around 12. my old 02 club car had been clocked at 21 MPH. this cart is not a...
View ArticleNeed wiring diagram
We think the cart is a 1988 but not sure. The mfg code is 60690 and serial number is 596776. Can someone tell me where I can find a wiring diagram?
View ArticleA few questions ezgo rxv
Hello to all, This is the first time working on an ezgo, RXV 2009 ser# 5042886 date code 1209. 1. Is it normal to only have one U bolt on each rear leaf spring? 2. How do you check the oil level in the...
View Article8 volt Battery question
My 8 volt batteries are completely dead, only about 2.5 v each in my 87 Marathon. They are new but it set for about 4 months. My regular charger won't \kick on. I have a normal 12 v car charger. How...
View ArticleSmall hole in battery case,repair?
Batteries were not anchored in,one slid and has a small cut in it, all the acid leaked out, 2 questions,#1 will hot glue repair the small cut? #2 will I need to just add distilled water,or do I need to...
View Article2009 RXV rear hub question
Hello to all, Jacked up this cart and rear wheels seem loose. Lug nuts are tight. The axle bolt is only finger tight on both sides. pulled the hubs off no teeth are missing on axle or hub. Put the hubs...
View ArticleWTB Driven clutch, 1986 Marathon
I need some or all of a driven clutch, particularly the front sheave. If someone has a messed up clutch which has a good front sheave, or I can buy the entire thing.
View ArticleBad Boy Classic
I need info on Bad Boy Classic. We have changed the switch, both solenoids, both motors are working fine. It will not move. We need all diagrams, schematics anyone will share. Help, Please
View Article99 Yamaha For Sale in my area with issues
http://miami.craigslist.org/pbc/snw/5362820447.html Found this cart on CL and looking to get into a new project. But he claims there is noise in the transmission ( im guessing rear end) How big of a...
View Articleoil pressure
Hi all. Got a problem with oil getting to valves on a buddies g14 cart. He completely rebuilt the motor with new valves rods crank and a 20 over piston. Issue is it isnt sending oil to vavles. Started...
View Article